Ensc 324 | Electronic Engineering homework help

ENSC 324 HOMEWORK #2 Fall 2015



DUE: Monday October 19, 2015 at 2 PM (note new time!)




Please note that unless you show work in the derivations and solutions you will get no credit for the


answers. Obviously copied answers from study partners or other sources, etc., will also receive no credit.



Please do all parts of all eight problems. It is suggested that you make a copy of your homework before




turning it in in case it cannot be returned before Exam 2 (solution key will be provided).



Problem #1




In a particular sample of n-type silicon, the Fermi energy level varies linearly with distance over a short



range. At x=0, the difference between the Fermi level and the intrinsic Fermi level is 0.4 eV. At x=10-3


cm, the same difference is only 0.15eV. The electron diffusion coefficient is 25 cm2/s.




a) Write an expression for the Fermi level with respect to the intrinsic fermi level versus distance.


b) What is the electron concentration versus distance?



c) What is the electron diffusion current density at x=0, and at x=5 x 10−4 cm?




Problem #2



A rectangular bar shaped silicon semiconductor resistor with a cross-sectional area of 100 μm2,


and a length of 0.1 cm, is doped with a concentration of 5 x 1016 cm−3 arsenic atoms (and no


acceptors). Let T = 300 K. A bias of 5V is applied across the length of the silicon resistor.



a) Calculate the current in the resistor.

b) Repeat part a) if the length is reduced by 0.01 cm.


c) What is the drift current in parts a) and b)?




Problem #3



Assume we have silicon with typical mid-range doping levels of donors (no acceptors) at 300K. Assume


that the mobility for electrons is limited by lattice scattering and has a temperature dependence of



approximately T-3/2. Determine the electron mobility at: a) T=200K; b) 400K.




Problem #4



A silicon bar has a length of L = 0.1 cm and a cross-sectional area of A = 10−4 cm2. The


semiconductor is uniformly doped with phosphorous at a level 5 x 1016 cm−3 (no other doping).



A voltage of 5 V is applied across the length of the material which is at T=300K. The minority

carrier lifetime is 3 x 10−7 s. For t < 0, the semiconductor has been uniformly illuminated with


light, producing a uniform excess carrier generation rate of g‘ = 5 x 1021 cm−3 s−1. At t = 0, the



light source is turned off. Determine the current in the semiconductor as a function of time for -∞

t ≥ ∞.




Problem #5



An n-type GaAs semiconductor at 300 K is uniformly doped with donors (no acceptors) at a

level of 5 x 1015 cm−3 (mid level doping). The minority carrier lifetime is 5 x 10−8 s. A light


source is turned on at t = 0 generating excess carriers uniformly at a rate of g‘ = 4 x 1021 cm−3 s−1.



There is no external electric field.

a) Determine the excess carrier concentrations versus time over the range 0 ≤ t ≤ ∞.



b) Calculate the conductivity of the semiconductor versus time over the same time period as

part (a).




Problem #6



Consider a bar of p-type silicon material at T=300K that is homogeneously doped to a value of 3

x 1015 cm−3 (ND=0), which may be considered mid level doping. The applied electric field is



zero. A light source is incident on the end of the semiconductor on one end (where x = 0, with x

increasing into the silicon bar). The excess carrier concentration generated at x = 0 is 1013 cm−3.



The lifetimes for electrons and holes are 0.5 μs and 0.1 μs, respectively.


a) Calculate the steady-state excess electron and hole concentrations as a function of


distance into the semiconductor.


b) Calculate the electron diffusion current density as a function of x.

Problem #7



Calculate the position of the quasi-Fermi level with respect to the intrinsic level for the following silicon



crystal that is steadily illuminated with an excess carrier generation rate of 1021 /cm3S:


NA = 1016 /cm3 , ND = 0


τn0 = τp0 = 1 μS




Problem #8



A silicon sample at 300K has the following impurity concentrations: ND = 1015 /cm3 and NA = 0 . The


equilibrium recombination rate is Rp0 = 1011 cm−3 s−1. A uniform generation rate produces an excess


carrier concentration of 1014 /cm3 .




a) What is the excess carrier lifetime?


b) By what factor does the total recombination rate increase?



Place your order
(550 words)

Approximate price: $22

Calculate the price of your order

550 words
We'll send you the first draft for approval by September 11, 2018 at 10:52 AM
Total price:
The price is based on these factors:
Academic level
Number of pages
Basic features
  • Free title page and bibliography
  • Unlimited revisions
  • Plagiarism-free guarantee
  • Money-back guarantee
  • 24/7 support
On-demand options
  • Writer’s samples
  • Part-by-part delivery
  • Overnight delivery
  • Copies of used sources
  • Expert Proofreading
Paper format
  • 275 words per page
  • 12 pt Arial/Times New Roman
  • Double line spacing
  • Any citation style (APA, MLA, Chicago/Turabian, Harvard)

Our guarantees

Delivering a high-quality product at a reasonable price is not enough anymore.
That’s why we have developed 5 beneficial guarantees that will make your experience with our service enjoyable, easy, and safe.

Money-back guarantee

You have to be 100% sure of the quality of your product to give a money-back guarantee. This describes us perfectly. Make sure that this guarantee is totally transparent.

Read more

Zero-plagiarism guarantee

Each paper is composed from scratch, according to your instructions. It is then checked by our plagiarism-detection software. There is no gap where plagiarism could squeeze in.

Read more

Free-revision policy

Thanks to our free revisions, there is no way for you to be unsatisfied. We will work on your paper until you are completely happy with the result.

Read more

Privacy policy

Your email is safe, as we store it according to international data protection rules. Your bank details are secure, as we use only reliable payment systems.

Read more

Fair-cooperation guarantee

By sending us your money, you buy the service we provide. Check out our terms and conditions if you prefer business talks to be laid out in official language.

Read more